|
Posted by on December 23, 2007, 4:08 am
Please log in for more thread options
On Thu, 08 Jun 2006 14:28:02 GMT, "Scott Townsend"
>So As I was walking in the Back 40 where the Tractor might be destined to
>live out its life... I decided to give it another whirl...
>
>So as I'm sitting on the unit with the fan on the opposite end of the engine
>then me the plugs are labeled on the Chassis as follows:
>
>2 1
>
>4 3
>
>So on the Cap I guessed that The connector where the Key on the Cap was
>located was 1, its the closest to being the one on top.
>
>from there on the Cap in clock wide I connected 1 -1, 2-2, 3-3, 4-4 So on
>the Cap I just went around in a circle from 1-4 and not 1,3,2,4 As it looked
>like you would not want to mix them twice, as I'm guessing you want the
>plugs to fire at opposite sides at each interval.
>
>So I had 3 and 4 Reversed according to the new wiring plan. (-;
>
>Swapped them, Tried starting it a few times. Blew the Oil input tube off,
>the dipstick went flying and I tried it a few more times...
>
>It Started!!!! Sounded 'okay' I'd here a pop here and there from the Oil
>input but it seems to have been running okay...
>
>Ran it for about 5 Minutes and then turned it off. Then could not get it
>stared again. )-; Then ran the Battery dead, so back on the charger...
>
>I was so Hopeful!!!
>
>Scott<-
>
>
><Ken Sterling (Ken Sterling)> wrote in message
>> >We have a Ditchwich Circa 1960 something with a Wisconsin VH4D, Spec
>> >408206,
>>>Serial 5804809 engine. Please be kind with me as my knowledge of engines
>>>is
>>>pretty minimal.
>>>
>>>After trying to get it to start for some time we replaced the Distributor
>>>Cap, Rotor, Wires and plugs, air and oil filters, and coil. We labeled
>>>all
>>>the wires for the plugs and are pretty sure that we have them all in the
>>>right place, though would like to be sure.
>>>
>>>There also seems to be quite a bit of back pressure in the engine and
>>>every
>>>once in a while trying to start it , the Dipsick will shoot out. I'm not
>>>sure if that could be caused by the miswiring of the plugs or not.
>>>
>>>Does anyone have this unit and could they tell me where the wires should
>>>go?
>>>
>>>Thank you,
>>> Scott<-
>>>
>>>
>> Scott,
>> 1. crank engine with distributor cap OFF, and note which direction
>> the rotor is turning...
>> 2. get number one piston to top dead center on the compression
>> stroke....
>> 3. when you re-install the distributor cap (with number 1 piston at
>> TDC on compression) the rotor will be pointing at the #1 tower on the
>> cap.....
>> 4. install wires on the cap in the correct firing order (1,3,4,2) in
>> the direction of rotor rotation...
>> problem should be solved other than minor "timing adjustment" provided
>> by rotating distributor a bit one direction or the other....
>> Hope this helps.
>> Ken.
>>
>
I just found this old message thread. I have an identical engine in a
skid loader. I also have an engine manual in .PDF format.
What ever happened to your engine? Did you get it running?
I'll email the manual to you via private email if you want it and post
a valid email address.
G.T.
| 
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML Sitemap